Product Search
Search results for 'D5856'
Showing 61 - 80 of 1122 Total Results
Speedy 2000 Moisture Tester 20 gr.
SA-0250
Location: Moisture Testing
The Speedy 2000 Moisture Tester from Test Mark is widely accepted for determining the free moisture content of a variety of materials - sand, aggregates, soil and other powders.
(2) options
Location: Test Platens
One fixture tests both 4” and 6” beams. . Used to determine the modulus of rupture for both Center and Third Point beams with depths of either 4” or 6”. The upper heads load bearing blocks are easily changed for center or third point test configuration for either size beam. Bottom support blocks...
SA-1050
Location: Dispersion Mixer
Test Mark's soil mixer is for dispersing solid suspensions used in hydrometer method of testing sub-grade soils.
Marshall Automatic Triple Compactor, 4" Rotating Mold
AA-0024
Location: Marshall Automatic Compactor
Automatically compacts three samples at a preset number of hammer blows and shuts off automatically on completion. Unit includes compactor, automatic counter, oak pedestal and 4" mold.
30 Gallon Water Tank - 24" x 18" x 18" deep (620 x 457 x 457 mm). Max. Oper. Temp. - 140°F (60°C)
CA-2742
Location: Parts & Accessories
Seamless, translucent tanks are ¼" (6.4 mm) thick with a drain faucet and overflow outlet. 30 Gallon (114L) tank is 24" x 18" x 18" deep (610 x 457 x 457 mm). Maximum operating temperature is 140°F (60° C).
44 Gallon Water Tank - 24" x 18" x 24" deep (610 x 457 x 610 mm). Max. Oper. Temp. - 140°F (60°C)
CA-2744
Location: Parts & Accessories
Seamless, translucent tanks are ¼" (6.4 mm) thick with a drain faucet and overflow outlet. 44 gallon tank is 24" x 18" x 24" deep (610 x 457 x 610 mm). Maximum operating temperature is 140°F (60° C).
AA-0040
Location: Marshall Hand Compaction Hammer
The Hand Compaction Hammer set from Test Mark Industries facilitates hand compaction of 4-inch samples.
Static Segregation Column Mold
CA-0359
Location: Self-Consolidating Concrete
The Static Segregation Column Mold is used to measure cohesiveness of SCC. Concrete is placed in the column and allowed to stand undisturbed. After 15 minutes, the top and bottom sections are evaluated for the amount of aggregate retained on a No. 4 (4.75 mm) sieve and segregation is calculated.
CA-2700
Location: Specific Gravity Flasks
The Chapman flask from Test Mark has two bulbs for determining approximate percentage of voids and surface moisture in fine aggregates.
CA-3125
Location: Vicat Apparatus
The Plastic Conical Mold from Test Mark is used with all Vicat Apparatus as part of a complete cement testing solution.
(4) options
Location: Test Platens
Test both cubes and cylinders . Used for testing 2” (50 mm) cubes and 3” (76 mm) diameter cylinders and cores in compression. Cube test set consists of a spherically seated platen assembly and a lower pedestal used for positioning the cube sample at the correct height for testing. The bearing block...
SA-2000
Location: CBR Load Frames
The CBR (California Bearing Ratio) loading press from Test Mark uses a two-position mechanical jack to provide steady test speeds, as well as rapid travel of the platen for positioning of the sample.
CA-3130
Location: Vicat Apparatus
Used with CA-3110 Modified Vicat Apparatus for false set determination, mold is 2" x 2" x 6" (50mm x 50 mm x 150mm). Overall length including base is 9 ¼" (240 mm).
AA-0050
Location: Asphalt
Circular, smooth-edged 4" diameter disc fits in bottom of 4" compaction molds prior to compaction test. Facilitates removal of sample specimen from mold.
CA-2720
Location: Specific Gravity & Absorption Fine Aggregates
The conical mold and tamper from Test Mark are used to determine bulk and apparent specific gravity and absorption of fine aggregate.
Circulating Water Bath, Digital
AA-0065
Location: Circulating Water Bath
The circulating water bath from Test Mark is fully insulated with magnetic circulator for heating up to 12 4-inch diameter Marshall samples at a time.
CA-0280-P
Location: Cube Molds
The high-density polyethylene three-gang mold for 2-inch cubes strips and reassembles easily. Easy ordering online from Test Mark Industries.
CA-0280
Location: Cube Molds
The 2-inch (51 mm) diagonal arrangement three-gang bronze cube mold from Test Mark makes three test cubes at a time.
